# 64–bit support is only available for USB products.
PicoLog displays data in a number of views, which can be activated as and when required. These views can be activated both during and after data collection.
Enables you to start/stop recording and specify recording files. It shows the current readings and alarm conditions for each channel. All settings such as scaling, channels and sampling are controlled from the recorder view.
XY graph view
Displays one parameter against another. Useful for plotting voltage against current, for example.
Displays text data in a format that can be easily ‘copied and pasted’ into other applications. Data can also be saved to disk in standard ASCII text format.
Graphs can be displayed both during and after data collection. Each channel can be displayed in its own graph or multiple channels can be displayed in the same graph. Axes can be set up manually, automatically or in chart recorder mode. Multipliers allow you to magnify areas of interest. Graphs can be ‘copied’ into the clipboard and then ‘pasted’ into reports.
Notes view allows you to attach notes to data.
Displays previously recorded data. It enables you to scroll quickly through stored files to compare results on successive runs. The player can be used to examine old data whilst new data is still being recorded.
PicoLog for Windows works in two modes: player mode for displaying previously recorded data and recorder mode for recording new data. You can have more than one copy of PicoLog for Windows running at once, so you can use the player to analyse old data whilst recording new data.
PicoLog can collect data from multiple converters at the same time. This not only allows a mix of voltage input units to be used on the same PC, but also allows other PC–based instruments such as the TC-08 Thermocouple Data Logger and the PicoScope 2200A USB Oscilloscopes to be used at the same time.
Data can easily be transferred (either as graphs or raw data) to other Windows applications by using the clipboard (copy and paste). Graphs can also be saved to disk (as Windows Metafiles) and data from the spreadsheet can be saved in text format. Current readings can be transferred using Dynamic Data Exchange (DDE). PicoLog also supports IP networking so it is possible to transfer measurements from a remote site via an existing LAN, company network, or even over the Internet.
Parameter Scaling can be used to convert raw data into standard engineering units. A wide range of equation and table lookup scaling options are provided.
Additional parameters can be calculated, for example to calculate power output from a boiler you may need to multiply a flow reading from one channel with the temperature difference between two further channels.
Alarm Limits can be set for each channel to alert the user should a parameter go out of a specified range.
PicoLog data acquisition software supports IP networking. This enables remote data collection from Pico’s full range of data acquisition products.
|Pico Technology PicoLog CM3 Current Data Logger, 3-Phase AC Current Signals||-||>|
|Rigol M300 Data Acquisition System||-||>|
|Rigol M301 Data Acquisition System including DMM||-||>|
|Rigol M302 Data Acquisition System including DMM, 20 channel MUX and M3TB20 terminal block||-||>|
|Pico Technology DrDAQ Kit||-||>|
|Pico Technology Pico TC-08 Thermocouple Data Logger||-||>|
|Pico Technology PT-104 Temperature Data Logger||-||>|
|Pico Technology ADC-20 Data Acquisition Unit||-||>|
|Pico Technology ADC-24 Data Acquisition Unit includes PP310 Terminal Board||-||>|
|Rigol MC3132 32 Channel Multiplexer Module||-||>|
|Rigol M3TB32 32 Channel MUX Terminal Box||-||>|
|Rigol MC3120 20 Channel Multiplexer Module||-||>|
|Rigol MC3164 64 Channel Reed Multiplexer Module||-||>|
|Rigol M3TB64 64 Channel MUX Terminal Box||-||>|
|Rigol MC3065 DMM Module||-||>|
|Pico Technology USB DrDAQ Data Logger (Logger Only)||-||>|
|Pico Technology DrDAQ DD100 Temperature Sensor||-||>|
|Pico Technology DrDAQ PP163 Humidity Sensor||-||>|
|Pico Technology DrDAQ DD011 pH Sensor||-||>|
|Pico Technology DrDAQ TA137 Redox Sensor||-||>|
|Pico Technology MI029 BNC Pug to 4 mm (Banana) Plug Cable, 1.2 m||-||>|
|Pico Technology DrDAQ EL302 Sensor Extension Cable, 3 m||-||>|
|Pico Technology PP216 Magnetic Induction Kit||-||>|
|Pico Technology PR121 USB TC-08 Single Channel Terminal Board||-||>|