Home Preamplifiers SRS SR570 Low Noise Current Preamplifier

SRS SR570 Low Noise Current Preamplifier

Availability: In stock


Product Code:
14984
Manufacturer: Stanford Research Systems
Special Price £2,537.52 £3,045.02 Regular Price £3,139.20
  • 5 fA/√Hz input noise
  • 1 MHz maximum bandwidth
  • 1 pA/V maximum gain
  • Adjustable bias voltage
  • Two configurable signal filters
  • Variable input offset current
  • Line or battery operation
  • RS-232 interface

More info and finance questions

Lambda Exclusive Promotion:
Additional 12 months warranty for free (2 years total) via our UK Service Centre.

The Stanford Research Systems SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SRS SR570 ideal for a variety of photonic, low temperature and other measurements.

Gain
The SR570 has sensitivity settings from 1 pA/V to 1 mA/V that can be selected in a 1-2-5 sequence. A vernier gain adjustment is also provided that lets you select any sensitivity in between.

Gain can be allocated to various stages of the amplifier to optimize the instruments performance. The low noise mode places gain in the front end of the amplifier for the best noise performance. The high bandwidth mode allocates gain to the later stages of the amplifier to improve the frequency response of the front end. In the low drift mode, the input amplifier is replaced with a very low input-current op amp, reducing the instrument’s DC drift by up to a factor 1000.

Filters
The SR570 contains two first-order RC filters whose cutoff frequency and type can be configured from the front panel. Together, the filters can be configured as a 6 or 12 dB/oct rolloff low-pass or high-pass filter, or as a 6 dB/oct rolloff band-pass filter. Cutoff frequencies are adjustable from 0.03 Hz to 1 MHz in a 1-3-10 sequence. A filter reset button is included to shorten the overload recovery time of the instrument when long filter time constants are used.

Input Offset and DC Bias
An input offset-current adjustment is provided to suppress any undesired DC background currents. Offset currents can be specified from ±1 pA to ±1 mA in roughly 0.1 % increments. The SR570 also has an adjustable input DC bias voltage (±5 V) that allows you to directly sink current into a virtual null (analog ground) or a selected DC bias.

Toggle and Blanking
Two rear-panel, opto-isolated TTL inputs provide additional control of the SR570. A blanking input lets you quickly turn off/on the instrument's gain which is useful in preventing front-end overloading. A toggle input inverts the sign of the gain in response to a TTL signal allowing you to perform synchronous detection with a chopped signal.

Battery Operation
Three rechargeable lead-acid batteries provide up to 15 hours of battery-powered operation. An internal battery charger automatically charges the batteries when the unit is connected to the line. The charger senses the battery state and adjusts the charging rate accordingly. Two rear-panel LEDs indicate the charge state of the batteries. When the batteries become discharged they are automatically disconnected from the amplifier circuit to avoid battery damage.

No Digital Noise
The microprocessor that runs the SR570 is "asleep" except during the brief interval it takes to change the instrument's setup. This ensures that no digital noise will contaminate low-level analog signals.

RS-232 Interface
The RS-232 interface allows listen-only communication with the SR570 at 9600 baud. All functions of the instrument (except power on) can be set via the RS-232 interface. The RS-232 interface electronics are opto-isolated from the amplifier circuitry to provide maximum noise immunity.

Input  
Inputs Virtual null or user-set bias (±5 V)
Input offset ±1 pA to ±1 mA adjustable DC offset current
Maximum input ±5 mA
Noise See graphs
Sensitivity 1 pA/V to 1 mA/V in 1-2-5 sequence (vernier adj. in 0.5 % steps)
Frequency response ±0.5 dB to 1 MHz. Adjustable front-panel frequency response compensation for source capacitance.
Grounding Amplifier ground is fully floating. Amplifier and chassis ground are available at rear panel. Input ground can float up to ±40 V.
   
Filters  
Signal filters 2 configurable (low-pass or high-pass) 6 dB/oct rolloff filters. -3 dB points are settable in a 1-3-10 sequence from 0.03 Hz to 1 MHz.
Gain allocation:  
Low noise Gain is allocated to the front end for best noise performance.
High bandwidth Front-end gain is reduced for optimum frequency response.
Low drift Low bias current amplifier is used for reduced drift at high sensitivity.
Filter reset Long time constant filters may be reset with front-panel button.
   
Output  
Gain accuracy ±(0.5 % of output + 10 mV) @ 25°C
DC drift see table below
Maximum output ±5 V into a high impedance load
   
General  
External blanking TTL input sets gain to zero
External toggle TTL input inverts gain polarity
Rear panel biasing ±12 VDC @ 200 mA, referenced to amplifier ground
Computer interface RS-232, 9600 baud, receive only
Power 100/120/220/240 VAC, 6 watts charged, 30 watts while charging. Internal batteries provide 15 hours of operation between charges. Batteries are charged while connected to the line.
Dimensions 8.3" × 3.5" × 13.0" (WHL)
Weight 15 lbs. (batteries installed)
Warranty One year parts and labor on defects in materials and workmanship
Write Your Own Review
You're reviewing:SRS SR570 Low Noise Current Preamplifier
Your Rating
Photo Product SKU
SRS SR555 Current Preamplifier SRS SR555 Current Preamplifier - >
SRS SR556 Current Preamplifier SRS SR556 Current Preamplifier - >
SRS SR560 Low-Noise Voltage Preamplifier SRS SR560 Low-Noise Voltage Preamplifier - >
SRS SR554 Transformer Preamplifier SRS SR554 Transformer Preamplifier - >
SRS SR552 BJT Input Preamplifier SRS SR552 BJT Input Preamplifier - >
SRS SR550 FET Input Preamplifier SRS SR550 FET Input Preamplifier - >
SRS SR445A Quad 350 MHz Preamplifier SRS SR445A Quad 350 MHz Preamplifier - >